Siemens SINUMERIK 802D sl Manuale dell'Operatore Pagina 209
- Pagina / 340
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Cycle alarms
06/2009 Overview of alarms
2-209
© Siemens AG 2009 All Rights Reserved
SINUMERIK 802D sl, Diagnostics Manual, 06/2009
61176 [Channel %1: ] Block %2: text length _DF programmed too small
Parameters: %1 = Channel number
%2 = Block number, label
Definitions: The text length in the engraving cycle is too short. This means that the text for engraving is longer than
the specified text length.
Reaction: Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy: Enter longer text length
Program Con-
tinuation:
Clear alarm with the RESET key. Restart part program
61177 [Channel %1: ] Block %2: polar text length > 360 degrees
Parameters: %1 = Channel number
%2 = Block number, label
Definitions: In the engraving cycle, the polar text length must not exceed 360 degrees.
Reaction: Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy: Enter shorter text length.
Program Con-
tinuation:
Clear alarm with the RESET key. Restart part program
61178 [Channel %1: ] Block %2: code page not present
Parameters: %1 = Channel number
%2 = Block number, label
Definitions: The specified code page is not supported by the cycle.
Reaction: Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy: Use code page 1252.
Program Con-
tinuation:
Clear alarm with the RESET key. Restart part program
61179 [Channel %1: ] Block %2: character does not exist, no.: %4
Parameters: %1 = Channel number
%2 = Block number, label
%4 = Character number
Definitions: The character entered in the text for engraving cannot be milled.
Reaction: Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy: Enter another character.
Program Con-
tinuation:
Clear alarm with the RESET key. Restart part program
61180 [Channel %1: ] Block %2: no name assigned to swivel data block,
although MD $MN_MM_NUM_TOOL_CARRIER > 1
Parameters: %1 = Channel number
%2 = Block number, label
Definitions: Although there are several swivel data blocks, no unique names have been assigned. Alarm triggered
by following cycles: CYCLE800.
Remedy: Assign unique names for swivel data blocks.
- SINUMERIK 802D sl 1
- SINUMERIK® Documentation 2
- Table of Contents I 7
- General alarms 11
- 1.4 System errors 12
- Overview of alarms 2 13
- NCK alarms 113
- 06/2009 Overview of alarms 113
- 2.2 Cycle alarms 193
- 2.3 Drive alarms 279
- 2.4 PROFIBUS alarms 281
- 2.5 PLC alarms 288
- 2.6 SINAMICS alarms 290
- List of action numbers 3 291
- Remedy 315
- System reactions on alarms 4 317
- Cancel criteria for alarms 320
- Appendix A 323
- Appendix 06/2009 324
- Abbreviations 324
- 06/2009 Appendix 325
- Feedback-340 340
Prodotti e manuali riguardandi Sistemi di controllo di accesso Siemens SINUMERIK 802D sl
(12 pagine)
(116 pagine)Sony RM-X169 manuels
Manuels d'utilisation et guides de l'utilisateur pour Panneau de contrôle Sony RM-X169.
Nous fournissons des manuels en pdf 1 Sony RM-X169 à télécharger gratuitement par type de document : Manuel de l'utilisateur
Commenti su questo manuale