Siemens SINUMERIK 802D sl Manuale dell'Operatore Scaricare il pdf (Pagina 19)

NCK alarms

06/2009 Overview of alarms

2-19

SINUMERIK 802D sl, Diagnostics Manual, 06/2009

4050 NC code identifier %1 cannot be reconfigured to %2

Parameters: %1 = String: Old identifier

%2 = String: New identifier

Definitions: Renaming of an NC code was not possible for one of the following reasons:

- The old identifier does not exist

- The new identifier lies in another type range.

NC codes/keywords can be reconfigured via machine data as long as the type range is not aban-

doned.

Type 1: "real" G codes: G02, G17, G33, G64, ...

Type 2: named G codes: ASPLINE, BRISK, TRANS, ...

Type 3: settable addresses: X, Y, A1, A2, I, J, K, ALF, MEAS, ...

Reaction: NC not ready.

Mode group not ready, also effective for single axes

NC Start disable in this channel.

Interface signals are set.

Alarm display.

NC Stop on alarm.

Remedy: Please inform the authorized personnel/service department.

Correct MD10712 $MN_NC_USER_CODE_CONF_NAME_TAB (protection level 1).

The list must be built up as follows:

Even address: Identifier to be modified.

Following odd address: New identifier

e.g.: $MN_NC_USER_CODE_CONF_NAME_TAB [10] = "ROT"

$MN_NC_USER_CODE_CONF_NAME_TAB [11] = " "

clears the ROT function from the control

Program Con-

tinuation:

Switch control OFF - ON.

4060 Standard machine data loaded (%1, %2, %3, %4)

Parameters: %1 = Identifier 1

%2 = Identifier 2

%3 = Identifier 3

%4 = Identifier 4

Definitions: The standard MD were loaded because

- a cold start was requested or

- the MD buffer voltage failed or

- an initialization was requested for loading the standard machine data (MD11200 $MN_INIT_MD).

Reaction: Alarm display.

Remedy: Please inform the authorized personnel/service department. After automatically loading the standard

MDs, the individual MDs must be entered or loaded in the relevant system.

Program Con-

tinuation:

Clear alarm with the RESET key. Restart part program

4062 Backup data loaded

Definitions: The user data saved in the flash memory are loaded to the SRAM.

Reaction: Alarm display.

Remedy: Load specific machine data again.

Program Con-

tinuation:

Clear alarm with the RESET key. Restart part program

4070 Normalizing machine data has been changed

Definitions: The control uses internal physical units (mm, degrees, s, for paths, velocities, acceleration, etc.). Dur-

ing programming or data storage, some of these values are input and output using different units

(rev./min, m/s2, etc.).

The conversion is carried out with the scaling factors that can be entered (system-spefic MD array

MD10230 $MN_SCALING_FACTORS_USER_DEF USER_DEF[n] (n ... index number 0 - 10), when

the corresponding masking bit is set to "1".

If the masking bit is set to "0" then scaling takes place with the internal standard factors.

The following machine data influence the scaling of other MDs:

MD10220: $MN_SCALING_USER_DEF_MASK

MD10230: $MN_SCALING_FACTORS_USER_DEF

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 339 340

Commenti su questo manuale

Nessun commento

Siemens SINUMERIK 802D sl Manuale dell'Operatore Pagina 19

Commenti su questo manuale

Prodotti e manuali riguardandi Sistemi di controllo di accesso Siemens SINUMERIK 802D sl