Siemens Pacemaker UM344-2 Manuale Utente Pagina 27
- Pagina / 183
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
INITIAL TRANSMITTER SET-UP UM344-2
September 1995
3
-
4
NOTE
Analog and Digital modes are
discussed in detail in Section 4.
5. The MXC will next prompt for a digital method of
searching. Press one of the following keys.
SHRT ADDR (F1) - Press and then enter the short
address (1-15) stored during configuration.
IMPORTANT
The factory default setting for the short
address is 0, analog mode.
LONG ADDRESS (F2) - Press and then enter the
long address stored in memory at the factory. (The
long address, the Dev. ID shown in the On-Line
Menu and the XMTR. ID shown by polling are the
same.) This address can not be altered.
POLL (F3) - Press to instruct the MXC to look for
any live addresses on the multi-drop network (1-15).
While the MXC is searching for one or more
transmitters, it will display SEARCHING. The MXC
will then display the long and short addresses of all
live transmitters on the network; select one by
pressing the SELECT (F4) key.
To view each of the live transmitters, press the
LAST XMTR and NEXT XMTR keys to scroll
forward and backward. Each screen will show the
transmitter ID number (i.e. device ID or long
address in hexadecimal), tagname, and short address.
Check IDs against user documentation to confirm
that all transmitters are present
If a problem exists in a transmitter or its wiring it will
be excluded from the poll. If a major fault exists in
the network wiring, the MXC will display the
warning message “NO TRANSMITTER FOUND”.
Go to section 6.3 Troubleshooting to confirm and
resolve wiring problems.
6. Communication has now been established between
the transmitter and MXC and the transmitter's
configuration has been uploaded to the MXC's On-
Line Memory.
ENTER TRANSMITTER
ADDRESS (1-15)
EN-
< END TER
SHORT OR LONG FORM
ADDRESS?
SHRT LONG
ADDR ADDR POLL END
ENTER TRANSMITTER
ADDRESS:
EN-
< END TER
SEARCHING FOR
TRANSMITTER
PLEASE WAIT
XMTR ID: 210100044F
TAG: MPCO 340 ADD: 01
LAST NEXT SEL-
XMTR XMTR END ECT
- USER’S MANUAL 1
- TABLE OF CONTENTS 2
- CONTENTS UM344-2 3
- September 1995 3
- UM344-2 CONTENTS 4
- September 1995 4
- SECTION AND TITLE PAGE 5
- LIST OF ILLUSTRATIONS 6
- LIST OF TABLES 7
- 1.0 INTRODUCTION 10
- FIGURE 1-1 Basic Model 344 11
- X02869S1 12
- 2.0 XTC COMMUNICATOR 14
- MOORE XTC COMMUNICATOR 15
- SELECT BLOCK TO EDIT 16
- - SENSOR INPUT 16
- PREV NEXT END ECT 16
- SELECT FUNCTION 18
- FIND ARCH TEST 18
- XMTR FUNC MXC END 18
- X02849S1 19
- LOOP OVERRIDE - CHOOSE 21
- CURRENT OUTPUT LEVEL 21
- 4 MA 20 MA OTHR END 21
- X02807S1 25
- SHORT OR LONG FORM 27
- ADDRESS? 27
- SHRT LONG 27
- ADDR ADDR POLL END 27
- MXC SELF TEST 28
- TEST TEST 28
- KEYS SCRN END 28
- WARNING! SELF TEST 30
- MAY BUMP TRANSMITTER 30
- OUTPUT A 30
- 4.0 INSTALLATION 35
- X02866S1 39
- X02867S1 40
- X02868S1 41
- X02817S1 42
- X02821S1 52
- Wall Mounting 53
- X02818S0 57
- FIGURE 4-8 Sensor Assembly 58
- X028AAS0 60
- X02870S1 61
- X02824S1 63
- TESTSIGNAL 66
- X02825S1 67
- MV LO : 0.0000 74
- ENTER MV LO: 74
- (F4) to change the setpoint 78
- DOWNLOADING 84
- CONFIGURATION 84
- - PLEASE WAIT 84
- DOWNLOAD 84
- COMPLETE 84
- MANUAL control mode to 92
- MANUAL control mode 92
- DG MR END CONT 96
- WARNING : ARCHIVE 97
- CONTAINS NO DATA 97
- A 97
- ERROR! ARCHIVE TYPE 98
- DOESN'T MATCH THE 98
- TRANSMITTER TYPE 98
- X02808S1 106
- X02827S1 1 of 2 111
- X02827S1 2 of 2 112
- APPLY 103.00 mV TO 115
- WITH COPPER WIRE 115
- CAL TEST END 118
- CALIBRATE / TEST 118
- TRANSMITTER PASSED 121
- TRANSMITTER SELFTEST 121
- 7.0 CIRCUIT DESCRIPTION 134
- Output Circuitry 135
- Input Circuitry 135
- X02815S0 142
- Z FS 146
- 9.0 GLOSSARY 154
- 4 - 20 mA 160
- Failsafe Level 160
- Absolute Alarm #1 161
- Absolute Alarm #2 161
- R = 162
- X02879S0 163
- Block Diagram, PD Controller 164
- Block Diagram, ID Controller 165
- X02881S1 168
- WARRANTY 177
- WARRANTY UM344-2 178
- W-2 October 1996 178
- PARTS LIST 179
- USER’S MANUAL ADDENDUM 181
- X03013S1 182
Prodotti e manuali riguardandi Misurazione, test & controllo Siemens Pacemaker UM344-2
(22 pagine)
(22 pagine)
Misurazione, test & controllo Siemens BTC-BR Manuale
(264 pagine)
(264 pagine)
© 2020, manymanuals.it. Tutti i diritti riservati | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale