Siemens S7 Manuale Utente Pagina 184
- Pagina / 222
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
NCM S7 Diagnostics
184
SIMATIC NET NCM S7 for Industrial Ethernet
C79000-G8976-C129–06
Other Startup Options
In the Properties dialog of the connections:
1. Select the PLC
"
Activate Connection Status menu command to activate
online access.
2. Select the “Special Diagnostics” button in the “Status Information” tab.
In the hardware configuration tool HW Config:
1. With the S7 station online, select the PLC
"
Module Status menu command;
2. Select the “Special Diagnostics” button in the dialog that is opened.
Note
To operate several diagnostic connections at the same time, you can start NCM
S7 Diagnostics more than once.
You can also start NCM S7 Diagnostics twice with an online connection to the
same CP; this can, for example, be useful if you want to monitor the diagnostic
buffer at the same time as running diagnostic functions on a connection.
Requirement: You have an online connection available via the LAN (ISO or
TCP/IP) on the one hand and an online connection via the communication (K) bus
on the other (alternatively via the CPU or via PG channel routing via a further CP).
- Audience 6
- Scope of this Manual 6
- Symbols used in this Manual 6
- Conventions 9
- Contents 10
- Stations 13
- 1.1 Industrial Ethernet 14
- Configuration and Diagnostics 18
- Industrial Ethernet 22
- Configuring S7 Connections 25
- Interface 27
- IP (Internet Protocol) 28
- SEND/RECEIVE interface 28
- Connection Types 30
- SIMATIC S5 30
- Configuring 31
- Networking in a Multiproject 31
- Variants 32
- Configuration of the System 33
- (Sub)Project 36
- Projects 39
- (TCP/IP) 41
- Ethernet Option 44
- 2.2 Procedure 45
- Procedure 46
- Subnet Attachment 49
- Graphic Overview in NetPro 52
- Overview in Table Form 53
- Options Tab 55
- S Assigning an IP address 56
- S Ethernet Profile for 56
- S Resetting module memory 56
- S Send Keepalives for 57
- S Multiplex OP Connections / 58
- Diagnostics Tab 59
- Addressing Tab 59
- Setting Up Connections 63
- Latest CPs) 64
- Requirements 65
- Alternative Procedure 67
- Principle 69
- Type of Interface 69
- Functions (FCs) 74
- Amounts of Data 74
- Purpose of the FCs 75
- Programming Connections 75
- 3.4 Additional Information 80
- Known Problems 81
- 4.1 Procedure 84
- 4.3 Connections 87
- Tasks of the Ethernet CP 88
- New Connection 90
- Unspecified Connections 94
- 4.3.3 Further Functions 96
- Display (Example) 98
- General Tab 100
- C79000-G8976-C129–06 101
- Address Parameters 102
- Addresses Tab 103
- TSAP Format 103
- Local and Remote TSAPs 103
- Default TSAPs 104
- Dynamics Tab 105
- Attributes AccessDescription 106
- Modifiable 106
- Display only 106
- Figure 4-11 107
- System Memory 108
- Links to Other Systems 108
- Overview Tab 109
- Introduction 110
- Opening the Dialog 110
- Address parameter 113
- Figure 4-16 116
- Figure 4-20 124
- Figure 4-21 125
- Application 134
- Figure 4-27 137
- 4.7.5 Free UDP Connection 139
- Routing to Distribute Load 140
- S7 Ethernet CPs 141
- Block Library 142
- Evaluating Status Codes 147
- Overview 148
- Working with the Job Header 151
- Meaning of the Block 152
- How the Block Works 153
- S Note the block type: 156
- S Note on the S7-400: 156
- Condition Codes 156
- DONE MeaningSTATUSERROR 158
- Example of AG_SEND 159
- NDR MeaningSTATUSERROR 166
- Caution when Configuring 167
- 5.4.1 FC7 AG_LOCK 169
- 5.4.2 FC8 AG_UNLOCK 171
- NCM S7 Diagnostics 175
- 6.1 Overview 176
- Functions 177
- Mode-Dependent Functions 177
- Installation 178
- Structure 179
- Operation 179
- 6.2.2 General Menu Commands 180
- S Dialog update time 181
- S Show TSAP in ASCII 181
- Ethernet CP 182
- Internetworking 183
- Other Startup Options 184
- 6.4 How to Use Diagnostics 185
- Firmware Loader 191
- 7.1 Application 192
- 7.2 Loading Firmware 193
- 2nd Step 194
- 3rd Step 194
- References 197
- Order Numbers 200
- Glossary 201
- B.1 General Section 202
- B.2 Industrial Ethernet 206
- B.3 PROFInet 208
- Linking to Other Systems with 211
- FETCH/WRITE 211
- “Parameter Values“ 212
- Parameter Values 214
- PI/PQ C T 215
- Document History 217
- A&D Technical Support 221
Prodotti e manuali riguardandi Software Siemens S7
Software Siemens Gigaset C675 IP Specifiche
(187 pagine)
(187 pagine)
Software Siemens COM32 Guida Utente
(126 pagine)
(126 pagine)
Software Siemens SIMATIC NET Guida Utente
(68 pagine)
(68 pagine)
Software Siemens Simatic S7-300 Manuale Utente
(26 pagine)
(26 pagine)
Software Siemens SIMATIC NET Specifiche
(268 pagine)
(268 pagine)
Software Siemens v1.0 Manuale di Servizio
(202 pagine)
(202 pagine)
Software Siemens S7-400 Manuale di Servizio
(382 pagine)
(382 pagine)
Software Siemens AC65 Guida Utente
(123 pagine)
(123 pagine)
Software Siemens Simatic M7-400 Manuale Utente
(266 pagine)
(266 pagine)
Sony RM-X169 manuels
Manuels d'utilisation et guides de l'utilisateur pour Panneau de contrôle Sony RM-X169.
Nous fournissons des manuels en pdf 1 Sony RM-X169 à télécharger gratuitement par type de document : Manuel de l'utilisateur
Commenti su questo manuale