Siemens B2Q191 Istruzioni per gli Interventi Pagina 28
- Pagina / 42
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
e1955
11.1999
28
Siemens Building Technologies
Cerberus Division
Remote transmission ISOLATE/DE–ISOLATE
This system is equipped with a remote transmission facility
for FIRE ALARM Yes, destination:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
No
for FAULT Yes, destination:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
No
What is «Remote transmission»?
Remote transmission establishes a transmission path to the fire department in the event of a FIRE ALARM.
For FAULT there is normally a separate path established.
When does the remote transmission have to be isolated?
Normally the remote transmission operates in active stand-by. Isolation is needed only in special cases, for ex-
ample for testing the control functions. For this test the
Remote alarm isolate key
1
on the control console
has to be pressed. The «ISOLATED» state is signalled by the indicator
2
.
123
456
789
ok
F2
F1
0
C
Alarms FaultsIsolationInformation
Alarm device Alarm deviceAlarm devicePremises
active faultisolate(d)manned
Remote alarm Remote transmissionRemote alarmAlarm delay
active faultisolate(d)off
Mains SystemControl functionDetector
available faultisolatedtest mode
2
1
ISOLATING the remote transmission
Press key
1
Ü The corresponding isolation message is displayed
Ü Indicator
2
turns on
Ü The FIRE ALARM remote transmission is isolated
DE–ISOLATING the remote transmission
Press key
1
(toggling key)
Ü Indicator
2
turns off
Ü The FIRE ALARM remote transmission is de–iso-
lated and switched to stand-by
Note
The remote transmission can also be isolated and de–isolated via the menu, separately for «Alarm» and
«Fault».
The remote transmission must be periodically checked by activating a manual call point. The fire department
must be notified before the test is initiated.
F1:function F2:menu
02 RT ’fire’ ISOLATED
factory
remote transmission channel FIRE
01 RT ’fire’ ISOLATED
remote transmission channel FIRE
main building
ISOLATION Zones: 0
- Cerberus® CS1145 1
- Fire detection system 1
- Operating instructions 1
- Operating instructions CI1145 3
- Introduction 4
- Operating access 5
- Control console layout 6
- Message categories 8
- What is an «Area»? 9
- What is a «Section»? 9
- What is a «Zone»? 9
- What is «Normal operation»? 10
- What is «Mains available»? 10
- Basic rules 11
- Automatic switchover 11
- Quick reference instructions 12
- Cerberus Alarm Concept 13
- Alarm – general information 14
- Alarm – what to do ? 16
- What is ISOLATION of a ZONE ? 18
- ZONE reactivation procedure 19
- Siemens Building Technologies 20
- Cerberus Division 20
- Mode ’Detector test’ 22
- Mode ’Installation test’ 26
- Mode ’Renovation’ 27
- Remote alarm isolate key 28
- ISOLATING the alarm devices 29
- Printer ISOLATE/DE–ISOLATE 30
- Spare paper rolls 31
- Print intensity 31
- Lamp test 32
- Alarm counter 33
- Event memory 34
- Set clock and date 35
- Overview operating menus 36
- To enter ’MAIN MENU’ press 40
Sony RM-X169 manuels
Manuels d'utilisation et guides de l'utilisateur pour Panneau de contrôle Sony RM-X169.
Nous fournissons des manuels en pdf 1 Sony RM-X169 à télécharger gratuitement par type de document : Manuel de l'utilisateur
Commenti su questo manuale