Siemens CM300/3 Manuale Utente

STÖBER CombiDrive®SIEMENS Micromaster integratedInstallation and Commissiong instructionsIt ist essential to read and comply with theseinstructions pr

English 2. Installation© STÖBER plc 199805.02.0181231231.8 mm max.ORFigure 4b: Connecting Control Wires to PL800Figure 2: Cable Connections with Dr

2. Installation English© STÖBER plc 1997905.02.012.3.3 Block Diagram3 ~MCPUA/DSIGRZKWRADAnalogue to Digital ConverterCPUMicroprocessorGRRectifierMMo

English 3. Operating Information© STÖBER plc 199805.02.01103. OPERATING INFORMATIONWARNINGThe equipment must not be switched on until after its cove

3. Operating Information English© STÖBER plc 19971105.02.01(2) Using a combination of the internal potentiometer and a run/stop switch:(a) Connect

English 3. Operating Information© STÖBER plc 199805.02.01123.6 If the Motor Does Not Start UpCheck the LEDs on the side of the inverter:LED State Co

3. Operating Information English© STÖBER plc 19971305.02.013.8 Closed Loop ControlClosed loop control is only possible when an OPm2 or a serial link

English 4. Clear Text Display Module & System Parameters© STÖBER plc 199805.02.01144. CLEAR TEXT DISPLAY MODULE & SYSTEM PARAMETERS4.1 Clea

4. Clear Text Display Module & System Parameters English© STÖBER plc 19971505.02.014.2 System ParametersThe parameters listed here can only be a

English 4. Clear Text Display Module & System Parameters© STÖBER plc 199805.02.0116Parameter Function Range[Default]Description / NotesP003 ••••

4. Clear Text Display Module & System Parameters English© STÖBER plc 19971705.02.01Parameter Function Range[Default]Description / NotesP007Keypad

ContentsSafety precautions... ..11. OVERVIEW ...

English 4. Clear Text Display Module & System Parameters© STÖBER plc 199805.02.0118Parameter Function Range[Default]Description / NotesP018 ••••

4. Clear Text Display Module & System Parameters English© STÖBER plc 19971905.02.01Parameter Function Range[Default]Description / NotesP027 ••••

English 4. Clear Text Display Module & System Parameters© STÖBER plc 199805.02.0120Parameter Function Range[Default]Description / NotesP051 Selec

4. Clear Text Display Module & System Parameters English© STÖBER plc 19972105.02.01Parameter Function Range[Default]Description / NotesP061Select

English 4. Clear Text Display Module & System Parameters© STÖBER plc 199805.02.0122Parameter Function Range[Default]Description / NotesP065Curren

4. Clear Text Display Module & System Parameters English© STÖBER plc 19972305.02.01Parameter Function Range[Default]Description / NotesP078 ••••

English 4. Clear Text Display Module & System Parameters© STÖBER plc 199805.02.0124Parameter Function Range[Default]Description / NotesP093 ••••

4. Clear Text Display Module & System Parameters English© STÖBER plc 19972505.02.01Parameter Function Range[Default]Description / NotesP123Enable

English 4. Clear Text Display Module & System Parameters© STÖBER plc 199805.02.0126Parameter Function Range[Default]Description / NotesP203 ••••

4. Clear Text Display Module & System Parameters English© STÖBER plc 19972705.02.01Parameter Function Range[Default]Description / NotesP910 ••••

© STÖBER plc 199805.02.01Safety PrecautionsBefore installing and putting this equipment into operation, please read these safety precautions andwarnin

English 5. Fault Codes© STÖBER plc 199805.02.01285. FAULT CODESFault codes are only available when an OPm2 is connected to the CombiDrive®.In the ev

6. Specifications English© STÖBER plc 19972905.02.016. SPECIFICATIONSCSA-single-phase deviceModel PM25/1 PM37/1 PM55/1 PM75/1Motor frame size: 4 pol

English 6. Specifications© STÖBER plc 199805.02.0130Input frequency: 47 Hz to 63 HzPower factor: λ ≥ 0.7Output frequency range: 0 Hz to 50 Hz (0 Hz t

6. Specifications English© STÖBER plc 19973105.02.01Options / AccessoriesClear Text Display (OPm2) 6SE3290-0XX87-8BF0Interface cable for OPm2 (length

English 7. Supplementary Information© STÖBER plc 199805.02.01327. SUPPLEMENTARY INFORMATION7.1 Application ExampleSetup procedure for a simple appl

7. Supplementary Information English© STÖBER plc 19973305.02.017.3 Electro-Magnetic Compatibility (EMC)Class 2: Filtered Industrial (Class A)This l

English 7. Supplementary Information© STÖBER plc 199805.02.01347.5 User's Parameter SettingsRecord your own parameter settings in the table bel

8. Accessoires© STÖBER plc 19973502.07.038.1 Control box (Steuerbox) for CombiDrive® integrated / connection diagramFunction Farben Number Designatio

8. Accessoires© STÖBER plc 199805.02.01368.2 Clear text Display Module (Opm2) in IP55 housingsee chap. 4.1.This section only applies for users who in

English 2. Installation© STÖBER plc 199805.02.0121. OVERVIEWThe CombiDrive® is an integrated motor/inverter for variable speed applications.The inve

Presented by: STÖBER ANTRIEBSTECHNIK GmbH + Co. KG GERMANY Kieselbronner

2. Installation English© STÖBER plc 1997305.02.012. INSTALLATIONWARNINGTo guarantee the safe operation of the equipment it must be installed and com

English 2. Installation© STÖBER plc 199805.02.0142.2 Mechanical InstallationFigures 1 and 2 show dimensional information for all CombiDrive® variant

2. Installation English© STÖBER plc 1997505.02.01CombiDrive® – Dimension (Only dimensions of the motor, total dimensions of the gear motor seeMGS-ca

English 2. Installation© STÖBER plc 199805.02.0162.3 Electrical InstallationRemove the four M5 cross-head screws on the inverter's cover to acc

2. Installation English© STÖBER plc 1997705.02.012.3.1 Mains Cable ConnectionsEnsure that the power source supplies the correct voltage and is desig